Various types of home appliance manufacturers, as well as institutions that conduct home appliance safety testing and certification, research institutes

Test Contents:

AC Hipot test, insulation resistance test, ground resistance test, leakage current test, run power and low voltage start performance test

Structure:

Floor-standing

Technical Parameters:

AC Hipot test
Booster rated output capacity			500VA (5000V/100mA), short circuit current is greater than 200mA
Output voltage waveform, distortion, adjustment rate			Sine wave, <3% (pure resistance,5000V/1mA), <3% (from empty load to full load)
Output voltage setting	Range		500～5000V
	Resolution, accuracy		5V,±(3%×setting+10V)
Frequency setting	Range, accuracy		50Hz/60Hz, ±0.1%×setting
Alarming limits setting	Current upper-limit		0.10~99.99mA
	Current lower-limit		0.00~10.00mA
Compensation current setting	Range		0.00~10.00mA, automatic testing, compensation can be set to ON/OFF
Time setting	Range		1~999s
	Ramp up time range		1~100s
	Accuracy		±(0.1%×setting+1count)
Breakdown current alarm	Range, accuracy		0.10~99.99mA, ±(3%×reading+3counts)
Insulation Resistance test
Rated output capacity			2VA(1000V/2mA)
Output voltage regulation, output voltage ripple			<3%(From no load to full load), <1%
Output voltage setting	Range, accuracy		DC 500V or 1000V, ±(3%×setting+3counts)
Alarming limits setting	Resistance upper-limit range		0.0~99.9 MΩ,100~2000MΩ(If upper-limit is set to 0, it will not make adjudgment for upper limit)
	Resistance lower-limit range		0.3~99.9 MΩ, 100~2000MΩ
Time setting	Range, accuracy		1~999s, ±(0.1%×setting+1count)
Insulation resistance measurement	Range		0.0~99.9 MΩ, 100~2000 MΩ
	Accuracy		≤200MΩ: ±(3%×reading+3counts) >200MΩ:±(8%×reading+8counts)
Ground Bond Resistance test
No load output voltage			<12V
Output current setting	Range, accuracy		3~30A, ±(3%×setting+0.2A)
Current frequency setting	Range, accuracy		Sine waveform 50Hz/60Hz, ±0.1%×setting
Test time setting	Range		1~999s
	Accuracy		±(0.1%×setting+1count)
Result display mode			Ground resistance or voltage
Ground resistance display mode
Alarming limits setting	Resistance upper-limit range		3A ≤ output current ≤ 10A:10~600 mΩ 11A ≤ output current ≤ 25A:10~300 mΩ 26A ≤ output current ≤ 30A:10~200 mΩ
	Resistance lower-limit range		0~100 mΩ
Compensation resistance setting	Range		0~200 mΩ, automatic testing, compensation can be set to ON/OFF
Ground bond resistance measurement	Range, accuracy		10~600 mΩ, ±(3%×reading+ 5counts)
Ground voltage display mode
Alarming limits setting	Voltage upper-limit range		30~7500 mV
	Voltage lower-limit range		0~3000 mV
Compensation voltage setting	Range		0~1000 mV, automatic testing, compensation can be set to ON/OFF
Ground bond resistance measurement	Range, accuracy		10~7500 mV, ±(3%×reading+ 50mV)
Leakage Current test
Leakage current test type setting			Single phase load, static/dynamic leakage current
MD network selection			Standard IEC 60990 figure 4 network; other test network optional
Alarming limits Setting	Current upper-limit range		0.050~9.999mA
	Current lower-limit range		0.000~5.000mA
Leakage current compensation setting	Range		0.000~1.000mA, automatic testing, compensation can be set to ON/OFF
Time test setting	Range, accuracy		1~999s, ±(0.1%×setting+1count)
Leakage current measurement	Range		0.050~9.999mA
	Accuracy		DC~10kHz: ± (3%×reading+0.010mA) 10 kHz ~1MHz: ± (5%×reading+0.050mA)
Output voltage measurement	Range, accuracy		60~280V(phase voltage), ±(0.5%×reading+2counts)
Run Power Only forAN9651S(F)/AN9651F(F)/AN9651B(F)
Alarming limits setting	Power upper-limit range		6~6000W
	Power lower-limit range		0~6000W
Test time setting	Range, accuracy		1~999s, ±(0.1%×setting+1count)
Voltage measurement	Range, accuracy		60~280V (phase voltage), ±(0.5%×reading+2counts)
Current measurement	Range, accuracy		0.030~3.999A, 4.00~25.00A, ±(0.5%×reading+2counts)
Active power measurement	Range, accuracy		30.0~199.9W: ±(0.5%×reading+5W), 200~6000W(or2000W): ±(0.5%×reading+30W)
Power factor measurement	Range, accuracy		0.10~1.00, ±(2%×reading+2 counts)
Low voltage start test
Alarming limits setting	Current upper-limit range		0.30~25.00A
	Current lower-limit range		0.00~25.00A
Test time setting	Range, accuracy		1~999s, ±(0.1%×setting +0.05s)
Voltage measurement	Range, accuracy		60~280V (phase voltage), ±(0.5%×reading+2counts)
Current measurement	Range, accuracy		0.030~3.999A, 4.00~25.00A, ±(0.5%×reading+2counts)
Power supply for UUT
SN2212B Built-in isolation transformer
Isolation transformer input voltage, frequency			Determined based on input voltage and frequency
Isolation transformer output voltage ratio	Leakage current test		The output voltage is 1.06 times the input voltage
	Run power test		The output voltage is 1.00 times the input voltage
	Low voltage start test		The output voltage is 0.85 times the input voltage
Isolation transformer capacity			Single phase load rated capacity 6000VA
Isolation transformer voltage regulation			3% (from no load to full load)
Overcurrent protection			Maximum current is 30A, automatically cut off the isolated power supply after 5s overcurrent
SN2212S, SN2212F Built-in variable frequency power supply
Max. output capacity			5000VA
Output voltage distortion			1% @ 47~63Hz
Output voltage stability			1%
Programmed output voltage		Voltage range	0~300V
		Voltage accuracy	0.5%RD+0.5%F.S.
Programmed output frequency		Frequency Range	47~63Hz
		Frequency stability	0.1%
Output maximum current		0~150V file	27A
		0~300V file	14A
SN2212S Configured IN-Pad
Processor			ARM926 core, 400MHz frequency
Operating system			Windows CE
Software			ESRS-Pad special software for safety test
Display			10.4” TFT color LCD
Operation method			Input through touch screen, support input through USB interface mouse and keyboard
Storage			50MB FLASH, user can choose large capacity SD memory card
External Interface			2-way RS232 interface, 2-way USB interface, CAN interface, DC12V power interface
Mounting brackets			3D, full angle, display stand
Bar code scanner			One barcode scanner with an RS232 interface defaulted
Interface function
Remote control interface			Standard, standard foot switch (start)
Alarm light interface			Standard, standard three-color warning light (test, qualified, warning)
Communication Interface			Standard RSA32, optional RS485, network port, GPIB, etc.
Variable frequency power control interface			Optional
Switch interface			Optional, start, stop, test, pass, alarm switch output
Printer interface			Optional, support for dot matrix printers and micro printers
General specification
Verification and calibration environment			23 ° C ± 5 ° C, (45 ~ 75)% RH, less dust
Use environment			0 ° C ± 40 ° C, (5 ~ 90)% RH, less dust
Storage environment			-10 ° C ~ 55 ° C, (5 ~ 95)% RH, less dust
System power			220V±10%, 50Hz±5%, 10A
System power consumption			Maximum 1000VA (excluding the operating power consumption of the tested product)
System weight (without packaging)			About 80kg
Dimensions (mm, without packaging)	SN2212S		483(W)x 600(D)x 1355(H)
	SN2212F		483(W)x 600(D)x 1355(H)
	SN2212B		530(W)x 460(D)x 1105(H)

Inquiry Cart 0